кликните сюда открыть старую версию сайта
Все категории
Parts by Car
Go
Parts by Car
Go
Каталог запчастей:
Категории

Nissan

Kolbenschmidt plain bearing measuring tape/plastic gauge 50009880

Part number 50009880.
Kolbenschmidt plain bearing measuring tape / plastic gauge kit (10 pcs.).
Measuring strips for the determination of bearing clearance for plain bearings

13,00 €
Permatex Ultra Slick assembly lubricant for engine bearings 118ml

Part number 81950
Permatex Ultra Slick assebly lubricant, lube oil for engine bearings.
Capacity 118 ml

12,00 €
ACL plain bearing measuring tape/flexigauge AG-1 (Green)
  1. Remove the bearing cap, wipe the journal and bearing shell clear of oil.
  2. Place a piece of Flexigauge across the bearing at the crown (see Figure 1).
  3. Install the bearing cap and using a Torque Wrench tighten the bolts to the correct tension.
    DO NOT REVOLVE THE SHAFT OR BEARINGS.
  4. Remove bearing cap. The Flexigauge will be adhering either to the bearing or shaft.
  5. Compare the width of the flattened Flexigauge with the graduation of the envelope. The figure within the graduations indicates the clearance in thousandths of an inch of millimetres, depending on which side of the envelope is used. (See Figure 2)
  6. Taper is indicated when Flexigauge is wider at one end than the other, the amount of taper being the difference between the readings. The widest part of the Flexigauge represents the area of least clearance. “Barrelling” of the shaft when the Flexigauge is wider in the centre of the bearing.


15,00 €
Nissan 1.6 1.7 1.8 2.0 ACL Race connecting rod bearings 4B1630H-STD
ENGINE BEARINGS
rods.jpg

CON ROD BEARING SET

Part#
4B1630H

4B1630HX

 
Sizes STD, .025, .25, .50 STD
Oil Clearance Standard + 0.001" Extra
Half Type Identical Halves
Material

Tri-metal Hardened steel backs

Min Std Shaft Size

1.7701in / 44.961mm

Max Std Shaft Size

1.7701in / 44.961mm

Min Std Tunnel Size

1.8898in / 48mm

Max Std Tunnel Size

1.8903in / 48.013mm

Max Wall at Crown

0.0593in / 1.505mm

0.0587in / 1.492mm

Max Overall Length

0.7323in / 18.6mm

Notes

Diagram       
(Top View) 

4B1630H.jpg
Engines Nissan - 1.6 1.7 1.8 2.0 (CA16, CA16DE, CA18, CA18DE, CA18ET, CA18DET, CA20E, CA20S, CD17)
65,00 €
Nissan SR20DE SR20DET ACL Race connecting rod bearings 4B2960H-STD

ENGINE BEARINGS
rods.jpg

CON ROD BEARING SET

Part#
4B2960H

4B2960HX

 
Sizes STD, .025, .25 STD
Oil Clearance Standard + 0.001" Extra
Half Type Identical Halves
Material

Tri-metal Hardened steel backs

Min Std Shaft Size

1.888in / 47.956mm

Max Std Shaft Size

1.8887in / 47.974mm

Min Std Tunnel Size

2.0079in / 51.000mm

Max Std Tunnel Size

2.0084in / 51.013mm

Max Wall at Crown

0.0592in / 1.503mm

0.0587in / 1.490mm

Max Overall Length

0.673in / 17.10mm

Notes

Diagram       
(Top View) 

4B2960H.jpg

Engines Nissan - 2.0 (SR20DE, SR20DET (not GTiR))

68,00 €
Nissan 1.6 1.7 1.8 2.0 ACL Race main bearings 5M1633H-STD
ENGINE BEARINGS
rods.jpg

MAIN BEARING SET

Part#
5M1633H

 
5M1633HX

 
Sizes STD, .025, .25, .50 STD
Oil Clearance Standard + 0.001" Extra
Half Type Upper & Lower
Material Tri-Metal
Min Std Shaft Size

2.0847in / 52.951mm

Max Std Shaft Size

2.0852in / 52.964mm

Min Std Tunnel Size

2.2305in / 56.654mm

Max Std Tunnel Size

2.231in / 56.667mm

Max Wall at Crown

0.0720in / 1.830mm  (1633H)
0.0722in / 1.835mm   (1635H - Flange)

0.0715in / 1.818mm  (1633HX)

0.0717in / 1.823mm (1635HX - Flange)

Max Overall Length

0.787in / 20.00mm         (1633H/HX)

1.100in / 27.95mm   (1635H/HX - Flange)

Notes

Diagram       
(Top View) 

1633H & HX - Positions 1, 2, 4, 5

1633H.jpg

1635H & HX - Position 3

1635H.jpg

Engines Nissan 4 cylinder 1.6L/1.7L/1.8L/2.0L
(CA16, CA16DE, CA18, CA18DE, CA18ET, CA18DET, CA20E, CA20S, CD17)
149,00 €
Nissan SR20DE SR20DET ACL Race main bearings 5M2964H-STD
ENGINE BEARINGS
rods.jpg

MAIN BEARING SET

Part#
5M2964H

 
5M2964HX

 
Sizes STD, .025, .25, .50 STD
Oil Clearance Standard + 0.001" Extra
Half Type Upper & Lower
Material Tri-Metal
Min Std Shaft Size

2.1636in / 54.956mm

Max Std Shaft Size

2.1646in / 54.980mm

Min Std Tunnel Size

2.3206in / 58.944mm

Max Std Tunnel Size

2.3216in / 58.968mm

Max Wall at Crown

0.0780in / 1.980mm

0.0774in /1.967 mm

Max Overall Length

0.752in / 19.10mm

Notes

Diagram       
(Top View) 

5M2964H.jpg
Engines Nissan 200SX - 2.0 (SR20DE, SR20DET (non GTiR))
109,00 €
Nissan SR20DE SR20DET ACL thrust washers kit 1T2964-STD
Part number 1T2964-STD
ACL thrust washer kit
Nissan - 2.0 (SR20DE, SR20DET)
15,00 €
Nissan SR20DE SR20DET ACL Race connecting rod bearings 4B2960HX-STD
ENGINE BEARINGS
rods.jpg

CON ROD BEARING SET

Part#
4B2960H

4B2960HX

 
Sizes STD, .025, .25 STD
Oil Clearance Standard + 0.001" Extra
Half Type Identical Halves
Material

Tri-metal Hardened steel backs

Min Std Shaft Size

1.888in / 47.956mm

Max Std Shaft Size

1.8887in / 47.974mm

Min Std Tunnel Size

2.0079in / 51.000mm

Max Std Tunnel Size

2.0084in / 51.013mm

Max Wall at Crown

0.0592in / 1.503mm

0.0587in / 1.490mm

Max Overall Length

0.673in / 17.10mm

Notes

Diagram       
(Top View) 

4B2960H.jpg
Engines Nissan - 2.0 (SR20DE, SR20DET (not GTiR))
68,00 €
Nissan 1.6 1.7 1.8 2.0 ACL Race connecting rod bearings 4B1630HX-STD
ENGINE BEARINGS
rods.jpg

CON ROD BEARING SET

Part#
4B1630H

4B1630HX

 
Sizes STD, .025, .25, .50 STD
Oil Clearance Standard + 0.001" Extra
Half Type Identical Halves
Material

Tri-metal Hardened steel backs

Min Std Shaft Size

1.7701in / 44.961mm

Max Std Shaft Size

1.7701in / 44.961mm

Min Std Tunnel Size

1.8898in / 48mm

Max Std Tunnel Size

1.8903in / 48.013mm

Max Wall at Crown

0.0593in / 1.505mm

0.0587in / 1.492mm

Max Overall Length

0.7323in / 18.6mm

Notes

Diagram       
(Top View) 

4B1630H.jpg
Engines Nissan - 1.6 1.7 1.8 2.0 (CA16, CA16DE, CA18, CA18DE, CA18ET, CA18DET, CA20E, CA20S, CD17)
65,00 €
Nissan Skyline RB25DET / RB26DETT ACL Race connecting rod bearings 6B2960H-STD
ENGINE BEARINGS
rods.jpg

CON ROD BEARING SET

Part#
6B2960H

6B2960HX

 
Sizes STD, .025, .25 STD
Oil Clearance Standard + 0.001" Extra
Half Type Identical Halves
Material

Tri-metal Hardened steel backs

Min Std Shaft Size

1.888in / 47.956mm

Max Std Shaft Size

1.8887in / 47.974mm

Min Std Tunnel Size

2.0079in / 51mm

Max Std Tunnel Size

2.0084in / 51.013mm

Max Wall at Crown

0.0592in / 1.503mm

0.0587in / 1.49mm

Max Overall Length

0.6732in / 17.1mm

Notes

Diagram       
(Top View) 

6B2960H.jpg
99,00 €
1 2 3